Homelink????
Thread Starter
Almost a Member!
Joined: Nov 2007
Posts: 29
Likes: 0
03 CL 500 sport, 97 Widebody NSX-T, 04 996 C4S, 02 528i sport, 06 GSX-R 600
Homelink????
anyone know how to set the buttons on the rearview mirror to read the signal for my garage door???
Thanks a million!!!
Thanks a million!!!
Administrator
Joined: Sep 2002
Posts: 15,769
Likes: 37
From: www.Traben-Trarbach.de
MPG+ ROLFCOPTER
Please give it more than 45 minutes between posts to get an answer. If you need to pass the time I'm sure its explained in your owners manual. Make sure you have it as well as your garage door opener manual. Another reference would be found by searching MBWorld. That question has come up numerous times for different MB models.
Junior Member
Joined: Jul 2003
Posts: 41
Likes: 4
From: Washington, D.C.
15 cls 550
you have to clear the memory before you program it (even the first time). I can't tremember exactly how you do it (I think you hold 2 buttons down for some period of time). It tells you how to clear the memory in the manual; it just doesn't mention that you have to do it before you first program the buttons.
Thread Starter
Almost a Member!
Joined: Nov 2007
Posts: 29
Likes: 0
03 CL 500 sport, 97 Widebody NSX-T, 04 996 C4S, 02 528i sport, 06 GSX-R 600
Please give it more than 45 minutes between posts to get an answer. If you need to pass the time I'm sure its explained in your owners manual. Make sure you have it as well as your garage door opener manual. Another reference would be found by searching MBWorld. That question has come up numerous times for different MB models.
Sorry.... I dont have a lot of free time to jack around on the computer so I post when I can.
Administrator
Joined: Sep 2002
Posts: 15,769
Likes: 37
From: www.Traben-Trarbach.de
MPG+ ROLFCOPTER
Junior Member
Joined: Jul 2003
Posts: 41
Likes: 4
From: Washington, D.C.
15 cls 550
Turn electronic key in starter switch to position 1 or 2.
SimultaneousTurn electronic key in starter switch to position 1 or 2.
Hold the end of your hand-held garage door opener approximately 2 to 5 inches (5 cm to 12 cm) away from the surface of the in-vehicle remote control located on the inside rear view mirror, keeping the indicator lamp in view.
Using both hands, simultaneously push the hand-held garage door opener button and the desired in-vehicle remote control button. Do not release the buttons until completing step 4.
The indicator lamp on the in-vehicle remote control will flash, first slowly and then rapidly. When the indicator lamp flashes rapidly, both buttons may be released (the rapid flashing lamp indicates successful programming of the new frequency signal). To program the remaining two remote control buttons, follow steps 1 through 4.
To clear memory:
Turn electronic key in starter switch to position 1 or 2.
Simultaneously hold down the left and right side buttons for approximately 20 seconds, or until the control lamp blink rapidly. This will erase the codes of all three channels.
SimultaneousTurn electronic key in starter switch to position 1 or 2.
Hold the end of your hand-held garage door opener approximately 2 to 5 inches (5 cm to 12 cm) away from the surface of the in-vehicle remote control located on the inside rear view mirror, keeping the indicator lamp in view.
Using both hands, simultaneously push the hand-held garage door opener button and the desired in-vehicle remote control button. Do not release the buttons until completing step 4.
The indicator lamp on the in-vehicle remote control will flash, first slowly and then rapidly. When the indicator lamp flashes rapidly, both buttons may be released (the rapid flashing lamp indicates successful programming of the new frequency signal). To program the remaining two remote control buttons, follow steps 1 through 4.
To clear memory:
Turn electronic key in starter switch to position 1 or 2.
Simultaneously hold down the left and right side buttons for approximately 20 seconds, or until the control lamp blink rapidly. This will erase the codes of all three channels.
Trending Topics
Thread Starter
Almost a Member!
Joined: Nov 2007
Posts: 29
Likes: 0
03 CL 500 sport, 97 Widebody NSX-T, 04 996 C4S, 02 528i sport, 06 GSX-R 600
Turn electronic key in starter switch to position 1 or 2.
SimultaneousTurn electronic key in starter switch to position 1 or 2.
Hold the end of your hand-held garage door opener approximately 2 to 5 inches (5 cm to 12 cm) away from the surface of the in-vehicle remote control located on the inside rear view mirror, keeping the indicator lamp in view.
Using both hands, simultaneously push the hand-held garage door opener button and the desired in-vehicle remote control button. Do not release the buttons until completing step 4.
The indicator lamp on the in-vehicle remote control will flash, first slowly and then rapidly. When the indicator lamp flashes rapidly, both buttons may be released (the rapid flashing lamp indicates successful programming of the new frequency signal). To program the remaining two remote control buttons, follow steps 1 through 4.
To clear memory:
Turn electronic key in starter switch to position 1 or 2.
Simultaneously hold down the left and right side buttons for approximately 20 seconds, or until the control lamp blink rapidly. This will erase the codes of all three channels.
SimultaneousTurn electronic key in starter switch to position 1 or 2.
Hold the end of your hand-held garage door opener approximately 2 to 5 inches (5 cm to 12 cm) away from the surface of the in-vehicle remote control located on the inside rear view mirror, keeping the indicator lamp in view.
Using both hands, simultaneously push the hand-held garage door opener button and the desired in-vehicle remote control button. Do not release the buttons until completing step 4.
The indicator lamp on the in-vehicle remote control will flash, first slowly and then rapidly. When the indicator lamp flashes rapidly, both buttons may be released (the rapid flashing lamp indicates successful programming of the new frequency signal). To program the remaining two remote control buttons, follow steps 1 through 4.
To clear memory:
Turn electronic key in starter switch to position 1 or 2.
Simultaneously hold down the left and right side buttons for approximately 20 seconds, or until the control lamp blink rapidly. This will erase the codes of all three channels.
Thank you very very very much!!!!
Ever in the Houston area... Beers on me!!!
MB World Stories
The Best of Mercedes & AMG
Manual Mercedes? 6 Times Sindelfingen Let Drivers Have All The Fun
Verdad Gallardo
Mercedes SLR McLaren 722 S Is Extremely Rare Example Modified by McLaren
Verdad Gallardo
8 Classic Boxy Mercedes Designs That Have Aged Like Fine Wine
Verdad Gallardo
Flawlessly Restored Mercedes 190E Evo II Heads to Auction
Verdad Gallardo
Electric Mercedes C-Class Unveiled: 11 Things You Need to Know
Verdad Gallardo
Mercedes EQS Gets A Major Update: Everything You Need to Know
Verdad Gallardo
5 Underrated Mercedes-Benz Models That Don't Get the Love They Deserve
Verdad Gallardo
Mercedes 300D Has Pushed Well Past 1 Million Miles and It Ain't Stopping
Verdad Gallardo
10 Most Reliable Mercedes-Benz Models You Can Buy Used
Verdad Gallardo
Senior Member
Joined: Sep 2004
Posts: 315
Likes: 2
From: Orlando, FL
2008 E350
If your garage door opener uses a "rolling code" you may want to check this thread:
https://mbworld.org/forums/showthrea...t=code+rolling
Hope this helps.
https://mbworld.org/forums/showthrea...t=code+rolling
Hope this helps.
Member
Joined: Mar 2008
Posts: 122
Likes: 29
From: Texas
S63 AMG Coupe AMG GT55
It took probably a full minute before the car "paired" with the remote,, so you may have to hold both the car button and the remote button down longer then "you feel you should have to". Once paired with the remote it was a snap recognizing the rolling code door opener.
