Where to begin
08-11-2022, 03:29 PM
#26
SPONSOR
iTrader: (4)
Join Date: Dec 2019
Location: WWW.BENZNINJA.COM
Posts: 2,685
Received 822 Likes
on
636 Posts
WWW.BENZNINJA.COM
9 days delivered in the US? I was looking into your service bensninja. If that's all I'll prob move foward with it, just to have in case. Can you show me the exact one to purchase? Cheapest too lol. I tried to download WIS from eBay but that was unsuccessful so hopefully plug and play.
please use this
copy paste this msg there and you'll recieve the info
https://benzninja.com/contact/
08-11-2022, 07:20 PM
#28
Member
Thread Starter
Is it ok to adopt the ism for direct select without my transmission pan on. Don't want to fill it again and bolt it up with single use bolts wasting time and money. Or is that a bad idea
08-18-2022, 05:54 AM
#32
Member
Thread Starter
Can you send me the correct one please or point me in the right direction then. Am I better off with the vcx style?
As far as my original issue. So I took off conductor plate and dropped in ultrasonic cleaner then finally was able to get car started. It also allowed me to actually clear what codes I had. Then of course when I go to take it down off ramps I guess the ism put a stop to that and I now have the following codes.
0778- pressure regulating valve 2 has an electrical fault.
2716- internal electrical test of component y38y for k3 clutch control solenoid valve has failed
2759- the pressure regulating valve of the torque converter lockup clutch has an electrical fault you up
C103 no can message was perceived from control unit n15-5 (electronic selector lever module control unit)
B210f00 circuit 30 has a malfunction
475600 no can message was received from control unit motor electronics
A3a813 The output for window heating has a malfunction. There's an open circuit
D19800 electronic ignition lock - communication with the ism has a malfunction
please God someone advise what to do.... currently loosing my mind
As far as my original issue. So I took off conductor plate and dropped in ultrasonic cleaner then finally was able to get car started. It also allowed me to actually clear what codes I had. Then of course when I go to take it down off ramps I guess the ism put a stop to that and I now have the following codes.
0778- pressure regulating valve 2 has an electrical fault.
2716- internal electrical test of component y38y for k3 clutch control solenoid valve has failed
2759- the pressure regulating valve of the torque converter lockup clutch has an electrical fault you up
C103 no can message was perceived from control unit n15-5 (electronic selector lever module control unit)
B210f00 circuit 30 has a malfunction
475600 no can message was received from control unit motor electronics
A3a813 The output for window heating has a malfunction. There's an open circuit
D19800 electronic ignition lock - communication with the ism has a malfunction
please God someone advise what to do.... currently loosing my mind
08-18-2022, 07:39 AM
#33
SPONSOR
iTrader: (4)
Join Date: Dec 2019
Location: WWW.BENZNINJA.COM
Posts: 2,685
Received 822 Likes
on
636 Posts
WWW.BENZNINJA.COM
Can you send me the correct one please or point me in the right direction then. Am I better off with the vcx style?
As far as my original issue. So I took off conductor plate and dropped in ultrasonic cleaner then finally was able to get car started. It also allowed me to actually clear what codes I had. Then of course when I go to take it down off ramps I guess the ism put a stop to that and I now have the following codes.
0778- pressure regulating valve 2 has an electrical fault.
2716- internal electrical test of component y38y for k3 clutch control solenoid valve has failed
2759- the pressure regulating valve of the torque converter lockup clutch has an electrical fault you up
C103 no can message was perceived from control unit n15-5 (electronic selector lever module control unit)
B210f00 circuit 30 has a malfunction
475600 no can message was received from control unit motor electronics
A3a813 The output for window heating has a malfunction. There's an open circuit
D19800 electronic ignition lock - communication with the ism has a malfunction
please God someone advise what to do.... currently loosing my mind
As far as my original issue. So I took off conductor plate and dropped in ultrasonic cleaner then finally was able to get car started. It also allowed me to actually clear what codes I had. Then of course when I go to take it down off ramps I guess the ism put a stop to that and I now have the following codes.
0778- pressure regulating valve 2 has an electrical fault.
2716- internal electrical test of component y38y for k3 clutch control solenoid valve has failed
2759- the pressure regulating valve of the torque converter lockup clutch has an electrical fault you up
C103 no can message was perceived from control unit n15-5 (electronic selector lever module control unit)
B210f00 circuit 30 has a malfunction
475600 no can message was received from control unit motor electronics
A3a813 The output for window heating has a malfunction. There's an open circuit
D19800 electronic ignition lock - communication with the ism has a malfunction
please God someone advise what to do.... currently loosing my mind
start by replacing the plate and testing the solenoid
08-18-2022, 03:56 PM
#34
Member
Thread Starter
Well I appreciate you chiming in before I went ahead with it again. I've never had to try so hard to put money in someone's pocket before. Are you going to tell me which is the correct one to order so I can use your service or would just like to continue chiming in after I've ****ed **** up.
08-18-2022, 04:11 PM
#35
MBWorld Fanatic!
Join Date: Apr 2019
Location: Silicon Valley
Posts: 5,661
Received 3,448 Likes
on
2,297 Posts
MY'14 W212 M276 3.5NA @60kMi
take it easy....
Well I appreciate you chiming in before I went ahead with it again. I've never had to try so hard to put money in someone's pocket before. Are you going to tell me which is the correct one to order so I can use your service or would just like to continue chiming in after I've ****ed **** up.
so communication may reflect that...
The concensus is he does excellent remote miracles
Follow his lead ✌️
The following 2 users liked this post by CaliBenzDriver:
AllPhonesAretap (09-01-2022),
juanmor40 (08-18-2022)
08-18-2022, 05:03 PM
#36
SPONSOR
iTrader: (4)
Join Date: Dec 2019
Location: WWW.BENZNINJA.COM
Posts: 2,685
Received 822 Likes
on
636 Posts
WWW.BENZNINJA.COM
Well I appreciate you chiming in before I went ahead with it again. I've never had to try so hard to put money in someone's pocket before. Are you going to tell me which is the correct one to order so I can use your service or would just like to continue chiming in after I've ****ed **** up.
if you give me your vin number
08-20-2022, 05:20 PM
#37
Member
Thread Starter
09-01-2022, 01:13 PM
#39
Member
Thread Starter
09-01-2022, 01:19 PM
#40
Member
Join Date: Dec 2021
Location: Calverton MD 20705
Posts: 144
Received 70 Likes
on
46 Posts
2013 W212 E350 RWD
Benz Ninja can get it to you in 14 days or less he said. Icarsoft told me I can change the Injector quantity adjustmenton a w212 but it can't. Blatantly false advertising. Icarsoft is only good for monitioring live data, has a lot of great live data.
