GL450 Mercedes-Benz ML GL 9" - 8.0 Oreo 4GB RAM Navigation System
Last edited by rich30769; May 27, 2020 at 05:46 PM.
This is basically the same layout except for the home screen
1 -- The backup camera only works sometimes, every 4th or 5th time i go in reverse the image will come up, other times, it is just a black screen
2 -- there is a very loud high pitched squeal that randomly occurs at least once every trip... the pitch is always the same but the volume and duration will change. it usually is so loud is scares the crap out of me while im driving. it will do it no matter what is connected or playing, radio, carplay (i have the wired adapter), or BT.
At this point my wife wants me to pull it out and put the original HU back in!
Please help!
1 -- The backup camera only works sometimes, every 4th or 5th time i go in reverse the image will come up, other times, it is just a black screen
2 -- there is a very loud high pitched squeal that randomly occurs at least once every trip... the pitch is always the same but the volume and duration will change. it usually is so loud is scares the crap out of me while im driving. it will do it no matter what is connected or playing, radio, carplay (i have the wired adapter), or BT.
At this point my wife wants me to pull it out and put the original HU back in!
Please help!
Does the backup camera work even with the unit off? Mine does. Don't know if that means anything at all.
It sounds to me like it's a wiring issue. Did you have someone install it for you? I installed my first unit myself and had a few minor issues, although nothing like you're having. I took it to a pro installer and he pulled the unit, disconnected some of my connections, reinstalled and it worked like a champ. I took the second unit to him for the initial install and have had no problems. If you have not had a pro look at it, I recommend it. Otherwise, I'm no help. Sorry.
The Best of Mercedes & AMG
Ask AVINUSA to send you another unit. That will solve your back up camera issues. They will ask for a deposit or have you send back the unit you have before they send a replacement.
The noise is most likely coming from a loose connection in the MOST adapter. Recheck the connection.
I hope this helps.
I hope this helps.
while we’re talking - do you or anyone else reading this know how to adjust the audio volume? When listening to music I need to turn up the volume on the head unit, but then audible warnings from Waze are too loud. Same with Siri. Need to turn up to hear her when texting, but then warnings way too loud.
i know there are volume settings in the Factory settings, but have not seen instructions for what is what.
while we’re talking - do you or anyone else reading this know how to adjust the audio volume? When listening to music I need to turn up the volume on the head unit, but then audible warnings from Waze are too loud. Same with Siri. Need to turn up to hear her when texting, but then warnings way too loud.
i know there are volume settings in the Factory settings, but have not seen instructions for what is what.
If its a new setup you might have the old file that the guide references in the docs that needs to be updated. I think there might be a way to boost the value of the amp in the factory settings part of settings, I haven't tried it yet though. I noticed I have to have the volume adjusted pretty loud though.
- my unit does not power down when I leave the car / lock it (it's almost like there's no sensing of ACC - just always on). Even an hour later, unit was still on. I have push button start; not sure if that works differently for ACC? Even opening the door does not work.
- I can't get the backup camera to work. I tried using a FAKRA to RCA adapter, but I think my NTG2 unit did not use FAKRA for the camera, oops. Can anyone help me figure out which pin I should tap into for the camera video signal? I read the entire thread and it looks like people use a pigtail and tap into the harness, but I can’t seem to find any posts that actually showed WHICH pin. [edit] I think this link is what I am looking for. I'm going to try this tomorrow, should work.
Last edited by Pseudo Nim; Sep 5, 2021 at 09:47 PM.
- my unit does not power down when I leave the car / lock it (it's almost like there's no sensing of ACC - just always on). Even an hour later, unit was still on. I have push button start; not sure if that works differently for ACC? Even opening the door does not work.
- I can't get the backup camera to work. I tried using a FAKRA to RCA adapter, but I think my NTG2 unit did not use FAKRA for the camera, oops. Can anyone help me figure out which pin I should tap into for the camera video signal? I read the entire thread and it looks like people use a pigtail and tap into the harness, but I can’t seem to find any posts that actually showed WHICH pin. [edit] I think this link is what I am looking for. I'm going to try this tomorrow, should work.
- my unit does not power down when I leave the car / lock it (it's almost like there's no sensing of ACC - just always on). Even an hour later, unit was still on. I have push button start; not sure if that works differently for ACC? Even opening the door does not work.
- I can't get the backup camera to work. I tried using a FAKRA to RCA adapter, but I think my NTG2 unit did not use FAKRA for the camera, oops. Can anyone help me figure out which pin I should tap into for the camera video signal? I read the entire thread and it looks like people use a pigtail and tap into the harness, but I can’t seem to find any posts that actually showed WHICH pin. [edit] I think this link is what I am looking for. I'm going to try this tomorrow, should work.
Any thoughts on my ACC problem? If you have a ML63, you probably had the same thing - I have a R63, so push button start etc. Did your experience any issues with the device staying on after ignition off?













