Updated 2010 w221 taillights on older w221
#326
Member
Join Date: Mar 2008
Location: Naples, FL
Posts: 193
Likes: 0
Received 0 Likes
on
0 Posts
S550 4matic, ML350
Hey Eric,
He is suggesting I try a modification to get it working first. If that doesnt work, Il do that.
Could you do me a favor? Can you tell me how the rear lights are supposed to look during normal operation?
What I mean is, there is 2 modes, I believe:
When you are driving with your lights off, are all 3 rows lit?
When you are driving with your lights on, are all 3 rows lit?
He is suggesting I try a modification to get it working first. If that doesnt work, Il do that.
Could you do me a favor? Can you tell me how the rear lights are supposed to look during normal operation?
What I mean is, there is 2 modes, I believe:
When you are driving with your lights off, are all 3 rows lit?
When you are driving with your lights on, are all 3 rows lit?
Other then that they are identical...
#327
Member
Join Date: Nov 2010
Location: San Francisco
Posts: 109
Likes: 0
Received 0 Likes
on
0 Posts
2008 G55
Ok, I just got a new set of lights from fishcake.
New ones work perfect, no errors and everything lights up, all 3 rows.
I have a early 2007 4matic s550
-Dan
New ones work perfect, no errors and everything lights up, all 3 rows.
I have a early 2007 4matic s550
-Dan
#328
Member
Join Date: Aug 2007
Posts: 236
Likes: 0
Received 0 Likes
on
0 Posts
mercedes 2011 CLS550 with AMG package
#329
Member
Join Date: Nov 2010
Location: San Francisco
Posts: 109
Likes: 0
Received 0 Likes
on
0 Posts
2008 G55
Its about a 30 minute job.
You need to remove the carpeted walls from the left and right sides, inside the trunk- This gives you access to the lights where you can unbolt them and slide new ones in.
#330
Member
Join Date: Aug 2007
Posts: 236
Likes: 0
Received 0 Likes
on
0 Posts
mercedes 2011 CLS550 with AMG package
I started the process and then only got to the removal of the first section where the trunk attaches and then . . . . . . . ok I better put it back together and go my buddies body shop.
#331
Member
Join Date: Aug 2007
Posts: 236
Likes: 0
Received 0 Likes
on
0 Posts
mercedes 2011 CLS550 with AMG package
I had a friend help me and they took 30 minutes or so to install. Plug and Play. they really look fantastic.
I purchased them on ebay from expresspart, and all the lights come on when the brakes are on as well. I like that vs the OEM because it is hard to miss that I am braking !!!
I purchased them on ebay from expresspart, and all the lights come on when the brakes are on as well. I like that vs the OEM because it is hard to miss that I am braking !!!
#332
Member
Join Date: Nov 2010
Location: San Francisco
Posts: 109
Likes: 0
Received 0 Likes
on
0 Posts
2008 G55
I had a friend help me and they took 30 minutes or so to install. Plug and Play. they really look fantastic.
I purchased them on ebay from expresspart, and all the lights come on when the brakes are on as well. I like that vs the OEM because it is hard to miss that I am braking !!!
I purchased them on ebay from expresspart, and all the lights come on when the brakes are on as well. I like that vs the OEM because it is hard to miss that I am braking !!!
#333
Member
Join Date: Aug 2007
Posts: 236
Likes: 0
Received 0 Likes
on
0 Posts
mercedes 2011 CLS550 with AMG package
did you get your from ExpressPart ???
#334
Member
Join Date: Nov 2010
Location: San Francisco
Posts: 109
Likes: 0
Received 0 Likes
on
0 Posts
2008 G55
#335
I want to order them today but don't know who to order from on e-bay. I know a while back when they first came out you had to modify them with a wire or get a sam. Did they fix it now so all you do is plug and play? And who should i get them from? fishcake or expresspart?
#337
Member
Join Date: Aug 2007
Posts: 236
Likes: 0
Received 0 Likes
on
0 Posts
mercedes 2011 CLS550 with AMG package
I want to order them today but don't know who to order from on e-bay. I know a while back when they first came out you had to modify them with a wire or get a sam. Did they fix it now so all you do is plug and play? And who should i get them from? fishcake or expresspart?
#338
Junior Member
Join Date: Aug 2010
Location: Cliffside Park, NJ
Posts: 21
Likes: 0
Received 0 Likes
on
0 Posts
2015 S550 4Matic, 2017 C300 4Matic. Retired, 2007 S550, 2014 CLS550 4Matic
Purchased mine from Expressparts also and I am very pleased with the look....
https://mbworld.org/forums/members/r...cs550pic70.jpg
https://mbworld.org/forums/members/r...cs550pic80.jpg
https://mbworld.org/forums/members/r...cs550pic70.jpg
https://mbworld.org/forums/members/r...cs550pic80.jpg
Last edited by rmajor; 07-13-2011 at 10:11 PM.
#339
Senior Member
Join Date: May 2011
Location: New York
Posts: 480
Likes: 0
Received 0 Likes
on
0 Posts
toyota sienna, S550, Subaru Outback
Purchased mine from Expressparts also and I am very pleased with the look....
https://mbworld.org/forums/members/r...cs550pic70.jpg
https://mbworld.org/forums/members/r...cs550pic80.jpg
https://mbworld.org/forums/members/r...cs550pic70.jpg
https://mbworld.org/forums/members/r...cs550pic80.jpg
Thanks!
#340
Junior Member
Join Date: Aug 2010
Location: Cliffside Park, NJ
Posts: 21
Likes: 0
Received 0 Likes
on
0 Posts
2015 S550 4Matic, 2017 C300 4Matic. Retired, 2007 S550, 2014 CLS550 4Matic
#341
#342
#343
Senior Member
Join Date: Mar 2004
Location: Ohio
Posts: 424
Likes: 0
Received 0 Likes
on
0 Posts
ML-350, Maserati Quattroporte
Ok, after following this thread for what seems like forever, it appears that the upgrade has evolved to a simple plug and play for about $500. Finally a cheap solution if we use the expressparts tail light. I am ready to pull the trigger myself but I would love a bit more detail(even photos) from rmajor, robertm and danodano on the install. How do I remove carpet, identify correct bolts and plug in wire?
#344
Junior Member
Join Date: Aug 2010
Location: Cliffside Park, NJ
Posts: 21
Likes: 0
Received 0 Likes
on
0 Posts
2015 S550 4Matic, 2017 C300 4Matic. Retired, 2007 S550, 2014 CLS550 4Matic
Ok, after following this thread for what seems like forever, it appears that the upgrade has evolved to a simple plug and play for about $500. Finally a cheap solution if we use the expressparts tail light. I am ready to pull the trigger myself but I would love a bit more detail(even photos) from rmajor, robertm and danodano on the install. How do I remove carpet, identify correct bolts and plug in wire?
You can view the finished look thru my photo album, the lights were installed by a recommended MB service and repair (private garage) but I don't have the name or remember the exact street address in North Hollywood.
I have since moved to the east coast. However, the folks over at Expressparts can give you their name.
The install took maybe 25 minutes start to finish, the carpet is simply peeled back and lifted out of the way but not removed, a few plastic moldings have to be removed along the edge of the trunk, paid the guy 75.00 to install both and I paid a few dollars less for the lights than the website has adverstised because as you will see in my photos I installed the smoked lens instead of the clear.
Absolutely no rewiring or reflashing work required, plug and play as stated, and no errors and way less expensive than the OEM for the purists, I understand, but I am good with minor mods and adjustments your dime, your choice.
If you want to discuss in directly PM me and send your contact details.
Rich
#347
Member
I just saw this.....what was the outcome?
Full View Re: MY EMAIL ADDRESS
From:FISH321 - NEW <fish321@speedstersource.com>
Add to ContactsTo:Morris Tate <skkons4@yahoo.com> 7 Files View Slideshow Download All
TL_MBZ_W221_RESISTOR.JPG (167KB); STEP1.JPG (143KB); STEP2_UNPLUG_WHITE_PLUG.JPG (105KB); STEP3_CUTOFF_WHITE_PLUG.JPG (121KB); STEP4_LEFT_SIDE.JPG (127KB); STEP5_PUSH_IN_RESISTOR.JPG (134KB); STEP6_RIGHT_SIDE.JPG (140KB)
#cg_msg_content DIV {MARGIN:0px;}If you or the installer can do it, we will be sending 2 black LED resistor as shown in the photo.
And what needs to be done is show in photos by the step. You have two ways to do it. Soldering or use tap splice.
FIRST WAY - Soldering:
Step 1. what you have received.
Step 2. un-plug the white plastic plug from the tail light
Step 3. cut off the white plastic plug tip and ready to solder to fuse the wires together.
Step 4. LEFT side should have BLACK to WHITE and RED to GRAY, if you solder the wires together and use heat shrink tube to shrink wrap once the soldering is done.
Step 5. Push in the new Black Resistor that we are supplying
Step 6. RIGHT side should have BLACK to GRAY and RED to WHITE, if you solder the wires together and use heat shrink tube to shrink wrap once the soldering is done.
SECOND WAY - Use tap splice, no soldering, this way is easier, but also less secure as sometimes the wires might get loose then it will loose the electrical contact, then lose the connection:
Step 1. what you have received.
Step 2. un-plug the white plastic plug from the tail light
Step 3. Use tap splices to connect as Step 4 and 6 for left and right sides following this simple instruction http://www.speedstersource.com/FISH/INSTALL_AE.htm
Step 4. LEFT side should have BLACK to WHITE and RED to GRAY, if you solder the wires together and use heat shrink tube to shrink wrap once the soldering is done.
Step 5. Push in the new Black Resistor that we are supplying
Step 6. RIGHT side should have BLACK to GRAY and RED to WHITE, if you solder the wires together and use heat shrink tube to shrink wrap once the soldering is done.
Let me know if you have any question, thanks.
Regards,
Simon
Dear fishcake321,
Error message: Tail lamp, brake lamp, right substitute bulb on.
On the left light, only reverse, blinker, and very top bulb (not led) is working. On right light, only reverse and very top bulb (not led) is working. None of the LED for the top or bottom rows are working, and only the left blinker works.
I understand your policy states that I have 3 business days upon receiving the item to contact you if item has been damaged during shipping or isn?t what described in your ad. Today is 22 Dec 2010; I received the item 21 Dec 2010. The ad states that I would have no error lights on instrument panel upon professional installation. Also, it states that all LEDs would work properly with no modifications. There is a very good chance that these lamps where damaged during shipping. All I know is they are not working at all like your ad described. I would like to talk to a customer service representative to get more information on where I need to return this item. Thank You...
- skkons4
From: fishcake321
To: skkons4
Subject: Re: skkons4 sent a message about 2010 LOOK MERCEDES W221 S550 S600 S63 S65 LED TAIL LAMP #120651490946
Sent Date: Dec-22-10 14:28:27 PST
Dear skkons4,
May I ask what kind of issue you have?
Did you encounter error saying rear side marker, left, right..etc and the top half LED is blinking?
Regards,
Simon
These tailights are not working properly. I went to a professional bodyshop to have installed. The dashboard has taillamp inop light, and they don't light properly. I paid a lot of money for this product. I'll return in same box tomorrow...
- fishcake321
From:FISH321 - NEW <fish321@speedstersource.com>
Add to ContactsTo:Morris Tate <skkons4@yahoo.com> 7 Files View Slideshow Download All
TL_MBZ_W221_RESISTOR.JPG (167KB); STEP1.JPG (143KB); STEP2_UNPLUG_WHITE_PLUG.JPG (105KB); STEP3_CUTOFF_WHITE_PLUG.JPG (121KB); STEP4_LEFT_SIDE.JPG (127KB); STEP5_PUSH_IN_RESISTOR.JPG (134KB); STEP6_RIGHT_SIDE.JPG (140KB)
#cg_msg_content DIV {MARGIN:0px;}If you or the installer can do it, we will be sending 2 black LED resistor as shown in the photo.
And what needs to be done is show in photos by the step. You have two ways to do it. Soldering or use tap splice.
FIRST WAY - Soldering:
Step 1. what you have received.
Step 2. un-plug the white plastic plug from the tail light
Step 3. cut off the white plastic plug tip and ready to solder to fuse the wires together.
Step 4. LEFT side should have BLACK to WHITE and RED to GRAY, if you solder the wires together and use heat shrink tube to shrink wrap once the soldering is done.
Step 5. Push in the new Black Resistor that we are supplying
Step 6. RIGHT side should have BLACK to GRAY and RED to WHITE, if you solder the wires together and use heat shrink tube to shrink wrap once the soldering is done.
SECOND WAY - Use tap splice, no soldering, this way is easier, but also less secure as sometimes the wires might get loose then it will loose the electrical contact, then lose the connection:
Step 1. what you have received.
Step 2. un-plug the white plastic plug from the tail light
Step 3. Use tap splices to connect as Step 4 and 6 for left and right sides following this simple instruction http://www.speedstersource.com/FISH/INSTALL_AE.htm
Step 4. LEFT side should have BLACK to WHITE and RED to GRAY, if you solder the wires together and use heat shrink tube to shrink wrap once the soldering is done.
Step 5. Push in the new Black Resistor that we are supplying
Step 6. RIGHT side should have BLACK to GRAY and RED to WHITE, if you solder the wires together and use heat shrink tube to shrink wrap once the soldering is done.
Let me know if you have any question, thanks.
Regards,
Simon
Dear fishcake321,
Error message: Tail lamp, brake lamp, right substitute bulb on.
On the left light, only reverse, blinker, and very top bulb (not led) is working. On right light, only reverse and very top bulb (not led) is working. None of the LED for the top or bottom rows are working, and only the left blinker works.
I understand your policy states that I have 3 business days upon receiving the item to contact you if item has been damaged during shipping or isn?t what described in your ad. Today is 22 Dec 2010; I received the item 21 Dec 2010. The ad states that I would have no error lights on instrument panel upon professional installation. Also, it states that all LEDs would work properly with no modifications. There is a very good chance that these lamps where damaged during shipping. All I know is they are not working at all like your ad described. I would like to talk to a customer service representative to get more information on where I need to return this item. Thank You...
- skkons4
From: fishcake321
To: skkons4
Subject: Re: skkons4 sent a message about 2010 LOOK MERCEDES W221 S550 S600 S63 S65 LED TAIL LAMP #120651490946
Sent Date: Dec-22-10 14:28:27 PST
Dear skkons4,
May I ask what kind of issue you have?
Did you encounter error saying rear side marker, left, right..etc and the top half LED is blinking?
Regards,
Simon
These tailights are not working properly. I went to a professional bodyshop to have installed. The dashboard has taillamp inop light, and they don't light properly. I paid a lot of money for this product. I'll return in same box tomorrow...
- fishcake321
#348
Junior Member
Join Date: Aug 2010
Location: Cliffside Park, NJ
Posts: 21
Likes: 0
Received 0 Likes
on
0 Posts
2015 S550 4Matic, 2017 C300 4Matic. Retired, 2007 S550, 2014 CLS550 4Matic
#349
Newbie
Join Date: Jul 2011
Location: rochester,ny
Posts: 6
Likes: 0
Received 0 Likes
on
0 Posts
mercedes benz s550 AMG P3
HELLPPPP
Hey im new to this forum i just picked up my self a S550 p3 package and trying to install the resistors on the wireing for each tail light. i took everything apart yesterday and got stuck. if any one could either provide a diagram or some pictures would really help out Thank you.
#350
Hey im new to this forum i just picked up my self a S550 p3 package and trying to install the resistors on the wireing for each tail light. i took everything apart yesterday and got stuck. if any one could either provide a diagram or some pictures would really help out Thank you.