RENNtech pulley kit 550$ :(
#101
#102
Junior Member
Thread Starter
Join Date: Sep 2007
Posts: 44
Likes: 0
Received 0 Likes
on
0 Posts
2003 C230 Kompressor Coupe
havent be participating because ive been quite busy over here(lame *** war) and do to the fact that people were going into dynos and fuel milage which i have no real knowledge of expect for the knowlegde i gain on the forum. im still here just waiting for a buyer
#104
Senior Member
Join Date: Oct 2008
Location: the ML/GL/R assembly line
Posts: 363
Likes: 0
Received 0 Likes
on
0 Posts
2005 C230 Kompressor
A heavily modded C32 that I had on a Schenk eddy current unit a couple of years back, with a decent cooling tower to control inlet air temp & a self calibrating broad range O2 sensor gave us the best power & torque curves with an AF ratio that was at about 14.2/1 up to 3500RPM & virtually flat at 13/1 all the way up to peak with final drop off at about 6300 where we went rich for safety - This vehicle was obviously blown.
The M271 is supposed to run at the lean end of stoichiometric - I will see if I can find some graphs. So it runs in the lean area. I'm not talking Toyota/Honda lean burn that run at 22/1 at low RPM coming closer to stoichiometric at high RPM (stratified charge)
Large American engines seem to like more fuel thrown at them to produce power.
The M271 is supposed to run at the lean end of stoichiometric - I will see if I can find some graphs. So it runs in the lean area. I'm not talking Toyota/Honda lean burn that run at 22/1 at low RPM coming closer to stoichiometric at high RPM (stratified charge)
Large American engines seem to like more fuel thrown at them to produce power.
#105
Junior Member
Join Date: Aug 2008
Location: Yonkers, NY
Posts: 51
Likes: 0
Received 0 Likes
on
0 Posts
2005 C230 Kompressor Sport Sedan
I figured the headers would be better towards working on my goal of getting a better engine/exhaust note from my car. I figure that a pulley system / ECU tuning could be a final project, with trying to do more intake/exhaust beforehand.
#106
Super Moderator
Ive never seen anything boosted that lean, like I posted before Ive been around domestic and import engines(including quads and bikes) on the dyno. I too am interested in the A/F mapping of the lean burn engines because just because someone hasnt seen something doesnt mean it doesnt happen or exist.
#108
I have a Brabus exhaust, its loud enough. Headers did little for the exhaust note, a little for the engine growl. The pulley definitely increased the SC whine, yet it depends if you like that sound.
#109
MBWorld Fanatic!
Join Date: Aug 2007
Location: Sacramento/San Gabriel/Riverside
Posts: 3,560
Likes: 0
Received 2 Likes
on
2 Posts
01' C32o
eisenman exhaust is all you need! I heard one on a C320, incredible sound!
I have a Brabus exhaust, its loud enough. Headers did little for the exhaust note, a little for the engine growl. The pulley definitely increased the SC whine, yet it depends if you like that sound.
I have a Brabus exhaust, its loud enough. Headers did little for the exhaust note, a little for the engine growl. The pulley definitely increased the SC whine, yet it depends if you like that sound.
#110
Super Moderator
#112
Send it to ROLLIN, since he initiated the name calling in response to "that's kinda a silly question" - yet as usual the person to retaliate gets reprimanded, not the original poster.
#113
Junior Member
Join Date: Aug 2008
Location: Yonkers, NY
Posts: 51
Likes: 0
Received 0 Likes
on
0 Posts
2005 C230 Kompressor Sport Sedan
#114
MBWorld Fanatic!
man this thread was good all day, and you had to go and say my name.... wonder why everyone's talking ish to you, can you really not see it??
#115
MBWorld Fanatic!
Ok here we go again. im just gonna have to prove this kid wrong again, sorry for the long post, but this dude just wont learn...
my first post
Im really interested in getting this, but i just had a couple questions, maybe someone can help out.... Do you know if this effects MPG at all and is it positive or negative. Should this be a pretty simple install, can i take it down to HMS and have them do it?? hopefully for cheap.... any help would be appreciated...
your reply
actually no i don't work on cars i pay people to do that... you need a job??? and yeah i'm sure you didn't want to write "silly," so hopefully you make it out to the show on the 11/15 and maybe you can say what you really wanted to... ill be at the DJ equipment most of the time and my name is Roland, why dont you come up and ask for me..
damn man, figure it out yet or what. Are you just that stupid?? when you type your replies, do you forget what you wrote before. Let me help you out, when you reply, read the whole thread 1st, every time, so when you do reply you dont make a complete *** out of yourself. But im sure you'll reply to this and say something stupid again.
Not uncool, information for the seller since he's already lowered his price once. Mine has been for sale on other forums all summer, no takers. M271 buyers are cheap and expect too much.
At $600 I could NOT sell it without being lowballed and all buyers backing out, especially since there is NO dyno that proves 20-25 hp gains. There was one dyno, yet I cannot find it anymore, broken link.
The gains are all at the low end (15-20hp), only minimal (5hp) gains at the top end due to the ECU nannies bleeding boost and retarding timing. This is why Kleemann sells the K-Box and the pulley + K-box costs $2K.
At $600 I could NOT sell it without being lowballed and all buyers backing out, especially since there is NO dyno that proves 20-25 hp gains. There was one dyno, yet I cannot find it anymore, broken link.
The gains are all at the low end (15-20hp), only minimal (5hp) gains at the top end due to the ECU nannies bleeding boost and retarding timing. This is why Kleemann sells the K-Box and the pulley + K-box costs $2K.
did you say you didn't start the name calling?? i'm not sure, do you want to say that again??
again sorry mbworld, moderators, and everyone else except akidonfire... i cant wait for his next reply. i'm sure he'll tell us he never even posted those words... someone broke into his account and claimed to be him
#116
Long post short: you're pathetic.
You called me "stupi..." and don't think that's name calling/insult?
Then you say you "pay people to do that" and offer "want a job?", a stuck up thing to say and demeaning insult towards those of us that do our own work.
As for "akidonfire" you should try turning a wrench and getting your hands dirty like a real man, then you can earn calling someone else a kid. I wish I could attend the meet, you're probably another manicured metro ***.
You're a stuck up pathetic loser hiding behind words.
I own my words, you should try it.
You called me "stupi..." and don't think that's name calling/insult?
Then you say you "pay people to do that" and offer "want a job?", a stuck up thing to say and demeaning insult towards those of us that do our own work.
As for "akidonfire" you should try turning a wrench and getting your hands dirty like a real man, then you can earn calling someone else a kid. I wish I could attend the meet, you're probably another manicured metro ***.
You're a stuck up pathetic loser hiding behind words.
I own my words, you should try it.
Last edited by amanonfire; 10-28-2008 at 10:14 PM.
#117
MBWorld Fanatic!
Join Date: Aug 2007
Location: Sacramento/San Gabriel/Riverside
Posts: 3,560
Likes: 0
Received 2 Likes
on
2 Posts
01' C32o
come on, let's stop this guys.
you both have contributed to the forum in many different ways. lets not try to get at each others necks please! i'm not gonna take sides, but seeing fellow w203 owner's fighting isn't pretty..
you both have contributed to the forum in many different ways. lets not try to get at each others necks please! i'm not gonna take sides, but seeing fellow w203 owner's fighting isn't pretty..
#118
MBWorld Fanatic!
Long post short: you're pathetic.
You called me "stupi..." and don't think that's name calling/insult?
Then you say you "pay people to do that" and offer "want a job?", a stuck up thing to say and demeaning insult towards those of us that do our own work.
As for "akidonfire" you should try turning a wrench and getting your hands dirty like a real man, then you can earn calling someone else a kid. I wish I could attend the meet, you're probably another manicured metro ***.
You're a stuck up pathetic loser hiding behind words.
I own my words, you should try it.
You called me "stupi..." and don't think that's name calling/insult?
Then you say you "pay people to do that" and offer "want a job?", a stuck up thing to say and demeaning insult towards those of us that do our own work.
As for "akidonfire" you should try turning a wrench and getting your hands dirty like a real man, then you can earn calling someone else a kid. I wish I could attend the meet, you're probably another manicured metro ***.
You're a stuck up pathetic loser hiding behind words.
I own my words, you should try it.
as i matter of fact i am a manicured, and cant leave out pedicured, metro.. hahaha... im sure some guys on the board can attest to that.. hahahaa
since im metro, you must be a hardcore gangster, grew up in the hood, handles his ish.. i can tell, you are just the man, cuz damn, you know what? you do own them words... dam, thats just hardcore. im scurrrrrrred
and right again i am hiding, in fact let me come out of hiding, i work off of crescent heights and sunset, you wanna do lunch tomorrow??
#119
MBWorld Fanatic!
damn Tommy you're right man, my bad again.... but come on this isn't really fighting.. this is nothing... i haven't even cussed yet but yeah i know, pretty lame huh?? hahaha... everytime i log in, i see some stupid ish, and i gotta say something...
#120
Junior Member
Thread Starter
Join Date: Sep 2007
Posts: 44
Likes: 0
Received 0 Likes
on
0 Posts
2003 C230 Kompressor Coupe
If you have forgot this thread was about selling a renntech pulley kit keep it clean and on topic start your own thread pertaining to different subjects(aka fighting, disagreements) thanks keep in civil
#121
MBWorld Fanatic!
my bad.. you haven't sold it yet??? i thought you had a buyer??
#122
MBWorld Fanatic!
Join Date: Sep 2008
Location: SoCal
Posts: 1,174
Likes: 0
Received 1 Like
on
1 Post
...a panty dropper...
I love how some threads turn into a pissing contest and it completely throws the original reason for the post to the grinder. Someone please take this kit off his hands so this thread can stop with the bickering.
#123
Super Member
Join Date: Feb 2007
Location: the LA-town, CA
Posts: 705
Likes: 0
Received 1 Like
on
1 Post
a w203 cÖuper
Im one of the buyers. Just waiting until Saturday to clear some funds. But im for sure i want this pulley since i can't find any other ones for the 1.8 m271 motor.
awomanonfire?!! That was pretty hilarious.
Someone's going on probation or getting
awomanonfire?!! That was pretty hilarious.
Someone's going on probation or getting