2nd to 3rd gear feels like a granny shift during race.
#1
Super Member
Thread Starter
Join Date: Jul 2008
Location: Brooklyn, NY/Tampa, FL
Posts: 831
Likes: 0
Received 0 Likes
on
0 Posts
2005 BLK/BLK E-Double Nickel.
2nd to 3rd gear feels like a granny shift during race.
So i raced a Stock CLS55 last night.(transmission on sport, dampers on sport2 and in gear 1) I caught the jump. 1st gear was smooth, shift to 2nd was good. 2nd gear also went smooth, however when car shifted from 2nd to 3rd it felt less agressive. CLS55 would gain big everythime i shifted from 2nd to 3rd. it wasnt a bog feeling, it was more of like a granny shift feeling. Any ideas??
Also i I did the tranny reset about 3 hours prior to race because car was feeling sluggish during shifts. Car no longer feels sluggish, just granny shifts to 3rd.
Also i I did the tranny reset about 3 hours prior to race because car was feeling sluggish during shifts. Car no longer feels sluggish, just granny shifts to 3rd.
#3
Super Member
Join Date: Oct 2009
Location: Saudi Arabia - Qatif
Posts: 661
Likes: 0
Received 3 Likes
on
3 Posts
Brabus K8 E55 05
I have smiliar issue but when shifting from 3rd to 4th, it takes time to shift like the car keep in same power for a while and then shifts so hard like something may came out the drive train.
I wish if anyone can give us any idea.
Transmission service was done recently, so it is not filter, or oil, or anything related to tranny service because I have had this issue before the service and still there.
I wish if anyone can give us any idea.
Transmission service was done recently, so it is not filter, or oil, or anything related to tranny service because I have had this issue before the service and still there.
#4
Super Member
Thread Starter
Join Date: Jul 2008
Location: Brooklyn, NY/Tampa, FL
Posts: 831
Likes: 0
Received 0 Likes
on
0 Posts
2005 BLK/BLK E-Double Nickel.
how long does adaptation take? i did 5-6 runs in total with the same outcome.
ahmad, how does your car differ since the tranny service?
ahmad, how does your car differ since the tranny service?
#5
Super Member
Join Date: Oct 2009
Location: Saudi Arabia - Qatif
Posts: 661
Likes: 0
Received 3 Likes
on
3 Posts
Brabus K8 E55 05
I have had this problem of delay and hard shifting since I did my mods "first with KLEEMAN header" but at that time it was not so hard like after installing the "TB82 + HE + IC pump".
Even when I serviced my tranny, nothing changed
My car is the same after service, I guess I was not running hard on my car most of the time.
Even when I serviced my tranny, nothing changed
My car is the same after service, I guess I was not running hard on my car most of the time.
#6
MBWorld Fanatic!
Join Date: Apr 2008
Location: Queens, NY
Posts: 1,762
Likes: 0
Received 1 Like
on
1 Post
04 w211 E55
So i raced a Stock CLS55 last night.(transmission on sport, dampers on sport2 and in gear 1) I caught the jump. 1st gear was smooth, shift to 2nd was good. 2nd gear also went smooth, however when car shifted from 2nd to 3rd it felt less agressive. CLS55 would gain big everythime i shifted from 2nd to 3rd. it wasnt a bog feeling, it was more of like a granny shift feeling. Any ideas??
Also i I did the tranny reset about 3 hours prior to race because car was feeling sluggish during shifts. Car no longer feels sluggish, just granny shifts to 3rd.
Also i I did the tranny reset about 3 hours prior to race because car was feeling sluggish during shifts. Car no longer feels sluggish, just granny shifts to 3rd.
http://www.youtube.com/watch?v=RP__DW2kmO8
#7
MBWorld Fanatic!
Car could be getting hot, I noticed the same thing happening at the track. Temps cooled down about 10 degrees when i was on my way home and the lag in the shift was gone. Do a little test, drive the car at a constant 60 mph jam the throttle see what happens, then do the same from a dead start and see if there's a difference.
Trending Topics
#9
Super Member
Join Date: Oct 2009
Location: Saudi Arabia - Qatif
Posts: 661
Likes: 0
Received 3 Likes
on
3 Posts
Brabus K8 E55 05
I still would like to know why there is a lagging in shifting when I accelerate hard on the car?
It takes long time to shift, yeah, it reaches close to 7000 rpm and does not want to shift then it shifts after some time, this delay in shift is really noticeable and it gets me lose a lot of time.
D S M, all modes has been tried, even without setting the gear to 1 and leaving it as it is on D or S.
Now, I can notice it from 1st to 2nd, don't know what's the reason !!!
Anyway help ??!!!
Suggestion??!!!
It takes long time to shift, yeah, it reaches close to 7000 rpm and does not want to shift then it shifts after some time, this delay in shift is really noticeable and it gets me lose a lot of time.
D S M, all modes has been tried, even without setting the gear to 1 and leaving it as it is on D or S.
Now, I can notice it from 1st to 2nd, don't know what's the reason !!!
Anyway help ??!!!
Suggestion??!!!
Last edited by ahmad0658; 11-20-2010 at 06:01 AM.
#10
Bump!!!!
I too noticed this while recently at the dragstrip this past weekend. Each pass was the same, 1st to 2nd would be fine and then a noticeable lag going from 2nd to 3rd. Feels like a lurch. Almost like the car is revving past redline and finally catches 3rd gear a quarter second later. I had someone else drive my car and he too felt the same thing. I was meaning to ask Jeremy (who was at the event) if he had any thoughts as to what may have been going on. I'm going to take my car to my independent shop to have them take a look.
Thoughts anyone??
I too noticed this while recently at the dragstrip this past weekend. Each pass was the same, 1st to 2nd would be fine and then a noticeable lag going from 2nd to 3rd. Feels like a lurch. Almost like the car is revving past redline and finally catches 3rd gear a quarter second later. I had someone else drive my car and he too felt the same thing. I was meaning to ask Jeremy (who was at the event) if he had any thoughts as to what may have been going on. I'm going to take my car to my independent shop to have them take a look.
Thoughts anyone??
#11
ok guys , last week i change it my body throttle ,engine mouths and gas pedal (warranty lol) honestly i got my car 45000miles on it and now 78miles ,after changing this things i feel its brand new trust me change body throttle first you will understand what i am talking about
#13
MBWorld Fanatic!
I still would like to know why there is a lagging in shifting when I accelerate hard on the car?
It takes long time to shift, yeah, it reaches close to 7000 rpm and does not want to shift then it shifts after some time, this delay in shift is really noticeable and it gets me lose a lot of time.
D S M, all modes has been tried, even without setting the gear to 1 and leaving it as it is on D or S.
Now, I can notice it from 1st to 2nd, don't know what's the reason !!!
Anyway help ??!!!
Suggestion??!!!
It takes long time to shift, yeah, it reaches close to 7000 rpm and does not want to shift then it shifts after some time, this delay in shift is really noticeable and it gets me lose a lot of time.
D S M, all modes has been tried, even without setting the gear to 1 and leaving it as it is on D or S.
Now, I can notice it from 1st to 2nd, don't know what's the reason !!!
Anyway help ??!!!
Suggestion??!!!
it has something to do with torq load limits i believe
#15
Super Member
Thread Starter
Join Date: Jul 2008
Location: Brooklyn, NY/Tampa, FL
Posts: 831
Likes: 0
Received 0 Likes
on
0 Posts
2005 BLK/BLK E-Double Nickel.
#17
Super Member
Join Date: Oct 2009
Location: Saudi Arabia - Qatif
Posts: 661
Likes: 0
Received 3 Likes
on
3 Posts
Brabus K8 E55 05
Mine is solved, tune problem
I have another problem and I hope it is the not the SC , I can hear that IC pump is not running since I have Meziere that is loud, but when switch off the car and start again, the meziere works and power own until I hit the accelerator more than half then the problem is on again
The car lose boost and drive like a diesel car
I will take it to be inspected by STAR today
I have another problem and I hope it is the not the SC , I can hear that IC pump is not running since I have Meziere that is loud, but when switch off the car and start again, the meziere works and power own until I hit the accelerator more than half then the problem is on again
The car lose boost and drive like a diesel car
I will take it to be inspected by STAR today
#18
MBWorld Fanatic!
who did the tune?
Mine is solved, tune problem
I have another problem and I hope it is the not the SC , I can hear that IC pump is not running since I have Meziere that is loud, but when switch off the car and start again, the meziere works and power own until I hit the accelerator more than half then the problem is on again
The car lose boost and drive like a diesel car
I will take it to be inspected by STAR today
I have another problem and I hope it is the not the SC , I can hear that IC pump is not running since I have Meziere that is loud, but when switch off the car and start again, the meziere works and power own until I hit the accelerator more than half then the problem is on again
The car lose boost and drive like a diesel car
I will take it to be inspected by STAR today
#21
Junior Member
Join Date: Sep 2007
Posts: 69
Likes: 0
Received 0 Likes
on
0 Posts
E55 2003, C32 2002,
I still would like to know why there is a lagging in shifting when I accelerate hard on the car?
It takes long time to shift, yeah, it reaches close to 7000 rpm and does not want to shift then it shifts after some time, this delay in shift is really noticeable and it gets me lose a lot of time.
D S M, all modes has been tried, even without setting the gear to 1 and leaving it as it is on D or S.
Now, I can notice it from 1st to 2nd, don't know what's the reason !!!
Anyway help ??!!!
Suggestion??!!!
It takes long time to shift, yeah, it reaches close to 7000 rpm and does not want to shift then it shifts after some time, this delay in shift is really noticeable and it gets me lose a lot of time.
D S M, all modes has been tried, even without setting the gear to 1 and leaving it as it is on D or S.
Now, I can notice it from 1st to 2nd, don't know what's the reason !!!
Anyway help ??!!!
Suggestion??!!!
#23
MBWorld Fanatic!
Join Date: May 2009
Location: Abu Dhabi
Posts: 1,484
Likes: 0
Received 13 Likes
on
9 Posts
C218 CLS63TT PP Edition1, W213 E63S
it used to be a tune problem.
but mine now shifts faster than before and it rocks.
i replaced SC bearings this week with roll bearings ( double bar ) instead of the single ball bearings ( stock ones) and it sure is smooth.
roll bearings was recomnded by alot of my friends as they never had a problem, not like the ball ones that comes as stock. they also withstand high rotations.
PS the X6M got in the drag 11.8x. lol it is about 670hp now.
next week im trying with E55 now that i got some Nitto Nt05 on it.
but mine now shifts faster than before and it rocks.
i replaced SC bearings this week with roll bearings ( double bar ) instead of the single ball bearings ( stock ones) and it sure is smooth.
roll bearings was recomnded by alot of my friends as they never had a problem, not like the ball ones that comes as stock. they also withstand high rotations.
PS the X6M got in the drag 11.8x. lol it is about 670hp now.
next week im trying with E55 now that i got some Nitto Nt05 on it.
Last edited by Ali_E55; 12-10-2010 at 02:37 AM.
#24
Super Member
Join Date: Oct 2009
Location: Saudi Arabia - Qatif
Posts: 661
Likes: 0
Received 3 Likes
on
3 Posts
Brabus K8 E55 05
it used to be a tune problem.
but mine now shifts faster than before and it rocks.
i replaced SC bearings this week with roll bearings ( double bar ) instead of the single ball bearings ( stock ones) and it sure is smooth.
roll bearings was recomnded by alot of my friends as they never had a problem, not like the ball ones that comes as stock. they also withstand high rotations.
PS the X6M got in the drag 11.8x. lol it is about 670hp now.
next week im trying with E55 now that i got some Nitto Nt05 on it.
but mine now shifts faster than before and it rocks.
i replaced SC bearings this week with roll bearings ( double bar ) instead of the single ball bearings ( stock ones) and it sure is smooth.
roll bearings was recomnded by alot of my friends as they never had a problem, not like the ball ones that comes as stock. they also withstand high rotations.
PS the X6M got in the drag 11.8x. lol it is about 670hp now.
next week im trying with E55 now that i got some Nitto Nt05 on it.
Where do I get these bearings in Abu Dhabi? Part number please.
#25
MBWorld Fanatic!
Join Date: Oct 2009
Location: Southern California
Posts: 2,825
Likes: 0
Received 16 Likes
on
11 Posts
E55 w/ goods, Z32 Project underway
it used to be a tune problem.
but mine now shifts faster than before and it rocks.
i replaced SC bearings this week with roll bearings ( double bar ) instead of the single ball bearings ( stock ones) and it sure is smooth.
roll bearings was recomnded by alot of my friends as they never had a problem, not like the ball ones that comes as stock. they also withstand high rotations.
PS the X6M got in the drag 11.8x. lol it is about 670hp now.
next week im trying with E55 now that i got some Nitto Nt05 on it.
but mine now shifts faster than before and it rocks.
i replaced SC bearings this week with roll bearings ( double bar ) instead of the single ball bearings ( stock ones) and it sure is smooth.
roll bearings was recomnded by alot of my friends as they never had a problem, not like the ball ones that comes as stock. they also withstand high rotations.
PS the X6M got in the drag 11.8x. lol it is about 670hp now.
next week im trying with E55 now that i got some Nitto Nt05 on it.
thanks