AJBoost

Hey fellas,

Well my cltuch/supercharger pulley is begining to rattle and sound very un AMG. Is there anyone who is selling either a stock or aftermarket one at this time? Please let me know.

Thanks,

Albert Hernandez

BenzTech415

Is it Chirping upon acceloration? Or is it noisy at idle? If it is just a chirp that can be easily fixed. If noisy at idle not so nice.

AJBoost

It's most noticable durring deceleration but at times at idle as well. It sounds like a loud rattle. I've removed the belt to isolate the problem and it seems to be the sc pulley.

AJBoost

Here's a related question...What's the current status of Code 3 Performance? Are they still a vendor, shipping parts, etc.? I ask because they are the only company i'm aware of that manufacture sc pullies.

Thanks.

Albert Hernandez.

loungn14

probably just the bearing in the sc pulley...

c3 = dead....

AJBoost

I hope its just the bearings, but after watching a crossfire pulley issue vid on youtube, i'm thinking its the backing plate rivits. Too bad about Code 3, are they out of business completely or just as a vendor here?

Albert Hernandez.

Here's the vid i'm talking about btw...
http://www.youtube.com/watch?v=0d-J2...eature=related

jturkel

wow....that was a good informational video..

and there is no way to get a stock pulley without the whole s/c'er correct? lol

TemjinX2

I would just risk it if i were you and buy a new sc bearing from code3. I believe their the only ones that sell that specific ngk bearing. I got mine in 3 days and it only cost me $20 to press in from a shop.

I think its worth the risk at $45 for the bearing.

loungn14

agreed....

Carl AMG

I just ordered an OE S/C bearing from Code 3 via their website this week and received information it has already shipped. The seem to be in business to me.

JG26_Irish

To me this sounds like a SC pulley bearing starting to go. The advice to replace the bearing is sound. If you are certain that it is indeed the SC clutch on the rear of the pulley, then PM me. I may be able to help you. I have a good SC pulley (stock). The sc bearing in it was starting to get noisy but the clutch portion is good. Replace the bearing and you would have a usable part. I have a new bearing but do not intend to sell it as I am keeping if for a spare. My advice is get the new bearing from C3P 1st and if that does not fix the problem, let me know and I can set you up with the rest of the pulley assembly. Since you will already have a good bearing at that point, it will not be wasted.

Irish

MJ50

might as well get code3 sc pulley...

AJBoost

Thanks for all the responses fellas. I'm extremely glad to hear code 3 is still shipping parts. Please update me when you recieve it. Many have had issues with the products arriving.

The supercharger clutch pulley CAN be ordered without the entire SC. But it costs, are you ready for this...$1200 without installation . Here's the most upseting part, Mercedes has a new updated version due to all the problems. Yet, for some reason will not recall the item and instead has left the cost to the customer. Not a good feeling when you remember what the C32's ran when new. I got better service when I had my Honda Accord as a teen.

Special thanks to the member who offered their stock one with the bad bearings. I intend to remove my pulley when I get home and double check the backing plate. If it is the plate, i'll be contacting you for sure about the stock unit.

The last option is the Code 3 pulley, altough the Crossfire forums have had some issues with the plate on these as well. So it is possible that the noise may return.


Thanks again to all who contributed,

Albert Hernandez.

ScottW911

Here is a possible fix...
http://cgi.ebay.com/ebaymotors/Merce...Q5fAccessories

This is a bit more than some, but alot less than most.

I purchased a spare S/C, some time ago, for an eventual clutch & pulley swap. Used C32 S/C's usually run between $300 and $3000 on ebay.

AJBoost

Wow, thats great to know. Thanks for the link. I'll be watching this to see where the price goes in the next few days. Too bad there isn't an option to buy it now.

Albert Hernandez.

AJBoost

Ok fellas,

After carefully examining the pulley i've diagnosed the problem. It is most certainly the backing plate. The bearings are as quite as when new. The plate and rivits on the other hand are obviosly creating the noise. Simply grabing the plate with gloves I could duplicate the sound without much effort.

SO... Now that i'm certain bearings won't sole the issue, anyone looking to go back to stock and sell their Code 3 pulley or even a stock pulley without the loose backing plate please contact me.


Thanks,

Albert Hernandez.

AJBoost

Hey Folks,

I'm still searching for a sc pulley, if anyone has one for sale please contact me.


Thanks,

Albert Hernandez

jturkel

try posting up over on the srt6 forum. maybe someone's got something over there

ScottW911

Only 2 days & 20 hours left on the eBay auction. It might just end up being the best value overall.

AJBoost

That's an awsome idea, i'm already on top of it. They too have a shortage of "good" pulley's for sale! lol



I couldn't agree more. I'm still watching it as well. Although I must admit the thought of more boost is very appealing! I'm e-mailing code 3 today to see what the availability on their pulley is.


Thanks for suggestions fellas,

Albert Hernandez

ScottW911

Good luck with that. I, personally, do not have a problem with Brandon or Code3. But, I sure have read a lot of posts from people who NEVER hear back from Code3.

Let us know if they get contact you.

moparrbust

LOL, I like how the guy says it's "for a 2005 or 2006 SLK 3.2 AMG"..............how many of those have you guys seen? It also cracks me up when he says "this supercharger should also fit a Chrylser Crossfire SRT-6"................it "SHOULD" fit because I can pretty much guarantee you that's what it came off of in the first place.



PS: I have personally seen 2 of these 2005/2006 SLK superchargers go for $200-300 on ebay.

AJBoost

I'm up late working, or is it early... Either way, I just checked my email and am happy to report code3 has already responded to me. A fella by the name of Brandon responded and seems to be very helpful. The only issue I have is the price of the pulley has changed since I last saw it. The original price was in the $500 range, but now it's listed for $650. I asked if he would honor the original price, hopefully he says yes. Is there something i'm not aware of regarding this discrepancy?


Thanks,
Albert Hernandez.

ScottW911

Cool. Brandon is the owner/founder of Code3. I am glad to see he responded.

As to the price, I do not recall the unit being priced at $500. I have always seen it at $650. Do not expect him to honor a price that may not have ever existed or has not been around for over a year.

02C32guy

I've been dealing with Brandon at code3 for a couple weeks now. I just ordered a heat exchanger and he has been really helpful and communicative. It's in the mail and should be here tomorrow! Your right about the price. Brandon had a sale the last few weeks. I got my heat exchanger for $349 and the regular price is $449. Unfortunately, it appears the sale is over.