Valvestud

Here is the sheet that defines the spec. In this case it's 325.6. The link below has all the various approved products. I use the Zerex G40.

Mercedes-Benz Operating Fluids

Regards,

Joe

Code7rpd

Hi Joe - you posted the information in the thread on replacing the inner track rod (tie rod) and outer tie rod, but it was for w212's with hydraulic steering. I'm not sure if that applies to cars with electric steering. Can you take a look based on my VIN to see if WIS lists the steps for the inner and outer rods? My VIN is WDDHF7GB7EA984434.

Valvestud

I really don't understand your request. To my knowledge all 2014 E63s have the same steering system. Where are you getting your info regarding electric versus hydraulic??

Code7rpd

I don't think I understand the steering system. I assumed it was electric since there is no power steering fluid reservoir. Are these systems still considered hydraulic?

Valvestud

The system is all electric. It replaced the need for the constantly running hydraulic pump. Regardless, our cars have the 211 option code, which is the electric steering. I believe most MB cars since around 2011 moved to electric. Any WIS docs I posted should be right assuming they were for model year 2014.

Code7rpd

Ok, perfect - I appreciate the help.

dustinN

Hi Joe,

Can I have the instruction for rear differential fluid change please? If possible, I would like to know what kind of fluid and part numbers for the drain & fill plugs as well. Thank you so much.

WDDLJ7EB3DA079389

Valvestud

Attached is the procedure. However, the procedure tied to your VIN indicates you have an LSD which is option code 471. Your datacard does not have the 471 listed. So, I'm not sure if you have LSD or not.

The fill and drain plug part number is A3529970032. The other attachment is the MB gear oils spec. You're looking for the 235.61 spec for your 218.374 car. I used the Castrol as per the link below in my car.

Mercedes-Benz Operating Fluids

Regards,

Joe

dustinN

Thank you, Joe. I'm glad I've asked. I thought I would need SAE 75W-90. But according to the MB gear oils spec, the correct one would be 75W-140. About the LSD with code 471, how can I find out if I have LSD or not? Does anyone know how to check for this? Thank you.

Valvestud

Not sure what to tell you about the LSD. Your VIN datacard says no LSD, but WIS procedure for the same VIN indicates it's for LSD rear end. Very strange. Perhaps someone else will respond with better info.

dustinN

I did the wheel spin test. Lifted the car up, put on N, spin the rear wheel on 1 side, the other wheel stayed still. That indicates I have standard differential and the oil specs is 235.7, 75W-85, correct?

Updated: Called MB dealer, provided them with VIN, they gave me Castrol Syntrax Limited Slip 85W-140. I am so confused.

Valvestud

Yes, therein lies the confusion. I researched other 2013 CLS63 and E63 VINs, and all of them in WIS indicate the oil change process is for cars with LSD, even if they don't have code 471 in their datacard! This would be why the dealer indicates the 85W-140 per the 235.61 spec for LSD cars. Your datacard shows the rear end to be non-LSD as your test confirms. What's goofy, it that I can't find a non LSD procedure for any E or CLS, (AMG or not). I even went to the procedures for a standard 2013 E350, and it still points to the procedure for LSD only cars.

Hopefully someone can jump in with knowledge.

Regards,

Joe

brade63s

Hey joe-
I was gonna see if you could get me info to replace the rear main seal. I think dropping the transmission would be the easiest but not sure on all the specs. It’s probably a lot of info for everything 😬
it’s a 2014 E63 S
vin WDDHF7GB6EA881215
thank you!

Valvestud

Attached are the procedures for removing trans and replacing rear main seal. There are numerous other sub-procedures. Let me know if you need something else.

Regards,

Joe

brade63s

thank you!!!

AMGfifty5

Hello @Valvestud

do you have the documents for replacing the front wheel bearing on 14 e63s?

WDDHF7GB1EA932152

tia

Valvestud

Attached.

Regards,

Joe

dustinN

Hi Joe,
Do you have documents for replacing TCU/TCM for '08E 350?
WDBUF56X08B290563
Thank you.

Valvestud

Hopefully this is you need. If not, please let me know.

Regards,

Joe

dustinN

Thank you. That's exactly what I need.

Zerocarpileup

VIN # 4JGDA7EB0DA116960

Does anyone have WIS for the thermostat on m157 2013 ML63. Greatly appreciated.

Krule77

I’d do the water pump and plastic cooling lines while your in there. Ifs not a fun job changing the worlds most expensive plastic thermostat the only thing worse would be going back in a month later to replace the water pump and cooling lines……. It’s a thing trust me. If Check all tensioners and idlers while your in there.


QUOTE=Zerocarpileup;8693684]VIN # 4JGDA7EB0DA116960

Does anyone have WIS for the thermostat on m157 2013 ML63. Greatly appreciated.[/QUOTE]

Valvestud

Procedure and Datacard attached. The are other procedures listed in the main one. Let me know if you need others

In case you need the part number for the thermostat/housing assembly, it's A2782000615.

Regards,

Joe

pkak2023

Hi Joe,
Do You have documents/instructions for removal of the entire dashboard instrument panel ?
WDDHF9BB7EA886684

Best Regards,
Paul

Valvestud

All of the relevant data that I believe is required. Lots of steps and special tools required. Let me know if you something else. Good luck!

Regards,

Joe