E63 S 4Matic M157 | Factory WIS Maintenance and repair documents
#201
MBWorld Fanatic!
Edit: I see now you put model info into your signature data. Correct procedure attached.
Regards,
Joe
Last edited by Valvestud; 06-08-2023 at 12:16 PM.
The following users liked this post:
Jaybird123 (06-08-2023)
#202
Member
Thanks so much for the quick response. I found 115Nm referenced in another post from a few years back, glad to see the official 130Nm value here!
I realize now that while I have the valve cover bolt tightening sequence and torque values, I don't have the sealant path pdf...do you have that one as well?
Now I owe you beers...but HOU is a bit out of range from KY. THANK YOU
I realize now that while I have the valve cover bolt tightening sequence and torque values, I don't have the sealant path pdf...do you have that one as well?
Now I owe you beers...but HOU is a bit out of range from KY. THANK YOU
#203
MBWorld Fanatic!
Thanks so much for the quick response. I found 115Nm referenced in another post from a few years back, glad to see the official 130Nm value here!
I realize now that while I have the valve cover bolt tightening sequence and torque values, I don't have the sealant path pdf...do you have that one as well?
Now I owe you beers...but HOU is a bit out of range from KY. THANK YOU
I realize now that while I have the valve cover bolt tightening sequence and torque values, I don't have the sealant path pdf...do you have that one as well?
Now I owe you beers...but HOU is a bit out of range from KY. THANK YOU
Regards,
Joe
#204
Member
Thank you, and hmm...those are the docs I have already...see where it says "Notes on sealant path for cylinder head cover AH01.30-P-1000-08MM" ? I was wondering if there is a document it is referring to here? I have such a sealant path doc for the front cam covers, but not for the valve covers. I can mostly follow where I have residue, but...
#205
MBWorld Fanatic!
Thank you, and hmm...those are the docs I have already...see where it says "Notes on sealant path for cylinder head cover AH01.30-P-1000-08MM" ? I was wondering if there is a document it is referring to here? I have such a sealant path doc for the front cam covers, but not for the valve covers. I can mostly follow where I have residue, but...
Regards,
Joe
The following users liked this post:
Jaybird123 (06-08-2023)
#206
Hi Joe,
I'm looking for instructions and part number list to remove and replace oil pan and gasket for 2014 E550.
VIN WDDHF9BB7EA886684.
Thank you,
Paul
I'm looking for instructions and part number list to remove and replace oil pan and gasket for 2014 E550.
VIN WDDHF9BB7EA886684.
Thank you,
Paul
#207
MBWorld Fanatic!
Hi Joe,
I'm looking for instructions and part number list to remove and replace oil pan and gasket for 2014 E550.
VIN WDDHF9BB7EA886684.
Thank you,
Paul
I'm looking for instructions and part number list to remove and replace oil pan and gasket for 2014 E550.
VIN WDDHF9BB7EA886684.
Thank you,
Paul
Regards,
Joe
#209
MBWorld Fanatic!
Regards,
Joe
#210
Junior Member
![Question](https://mbworld.org/forums/images/icons/icon5.gif)
Hey guys, figured id post the most up to date maintenance documents and repair procedures according to Mercedes Benz direct from the factory dealer WIS. WIS is what the techs use at the dealer and how benz wants these cars repaired, its a factory service manual in short.
These are good for 14-16 E63 S 4matics, but most will be good for early E63 M157 aswell!
I will add more if i think it may be helpful to the community.
Enjoy!
These are good for 14-16 E63 S 4matics, but most will be good for early E63 M157 aswell!
I will add more if i think it may be helpful to the community.
Enjoy!
#211
Member
![Smilie](https://mbworld.org/forums/images/smilies/smile.gif)
Do you have front strut replacement doc(s) for my m278? Not getting any response on the sub-forum dangit. I have the electronic dynamic pkg (483)
#212
MBWorld Fanatic!
Regards,
Joe
#213
Member
#214
MBWorld Fanatic!
#216
MBWorld Fanatic!
Apologies Joe, here is my VIN: WDDKJ7DB9EF228017
Regards,
Joe
The following users liked this post:
Jaybird123 (08-28-2023)
#217
Thanks a lot bro very helpful!!
can I find diagram or any thing about engine air system,, all tubes,vacuums , sensors,etc
my car may have an AIR LEAK pin the engine air system ((cls 63 2012)) 🧐🧐🧐
can I find diagram or any thing about engine air system,, all tubes,vacuums , sensors,etc
my car may have an AIR LEAK pin the engine air system ((cls 63 2012)) 🧐🧐🧐
#218
Hey guys, figured id post the most up to date maintenance documents and repair procedures according to Mercedes Benz direct from the factory dealer WIS. WIS is what the techs use at the dealer and how benz wants these cars repaired, its a factory service manual in short.
These are good for 14-16 E63 S 4matics, but most will be good for early E63 M157 aswell!
I will add more if i think it may be helpful to the community.
Enjoy!
These are good for 14-16 E63 S 4matics, but most will be good for early E63 M157 aswell!
I will add more if i think it may be helpful to the community.
Enjoy!
can I find diagram or any thing about engine air system,, all tubes,vacuums , sensors,etc
my car may have an AIR LEAK pin the engine air system ((cls 63 2012)) 🧐🧐🧐
#219
Out Of Control!!
Join Date: Jun 2004
Posts: 11,627
Received 1,990 Likes
on
1,393 Posts
2014 E63S; AMS 100 octane ecu tune; edok tcu tune; BB intakes; dyno tuned
Oil filter and oil housing torque specs thanks to @Valvestud
https://mbworld.org/forums/w212-amg/...que-specs.html
https://mbworld.org/forums/w212-amg/...que-specs.html
Last edited by PeterUbers; 03-20-2024 at 11:53 PM.
#221
MBWorld Fanatic!
#223
Out Of Control!!
Join Date: Jun 2004
Posts: 11,627
Received 1,990 Likes
on
1,393 Posts
2014 E63S; AMS 100 octane ecu tune; edok tcu tune; BB intakes; dyno tuned
@Valvestud do you have a document to discuss service recommendations for oil solenoid failure in the m157? Or for code P06DA00
thank you
thank you
#224
MBWorld Fanatic!
@Valvestud do you have a document to discuss service recommendations for oil solenoid failure in the m157? Or for code P06DA00
thank you
thank you
Regards,
Joe
The following users liked this post:
PeterUbers (04-03-2024)
#225
Out Of Control!!
Join Date: Jun 2004
Posts: 11,627
Received 1,990 Likes
on
1,393 Posts
2014 E63S; AMS 100 octane ecu tune; edok tcu tune; BB intakes; dyno tuned